Prototyping

DESCRIPTIONThis is a basic breakout board for the FTDI FT232RL USB to serial IC. The pinout of this board matches the FTDI cable to work with offic...

DESCRIPTIONThis is a simple breakout board for our RFID readers. The RFID Reader Breakout converts the 2mm pins to bread board friendly 0.1" header...

DESCRIPTION This is a clever little breakout board for both the RGB and R/G illuminated rotary encoders. On one side, it breaks out all of the RGB ...

DESCRIPTIONThis is a breakout board for the very handy 16-Channel Analogue/Digital Multiplexer/Demultiplexer CD74HC4067. This chip is like a rotary...

DESCRIPTIONThis simple board breaks out a micro-B USB connector's VCC, GND, ID, D- and D+ pins to a 0.1" pitch header. If you want to add the popul...

DESCRIPTIONThis is a board designed for opto-isolation. This board is helpful for connecting digital systems (like a 5V microcontroller) to a high-...

DESCRIPTIONThe SparkFun Serial Basic Breakout is an easy-to-use USB-to-Serial adapter based on the CH340G IC from WCH. It works with 5V and 3.3V sy...

DESCRIPTIONThe Si5351A clock generator breakout from Adafruit allows you to generate any clock frequency from 8Khz up to 160MHz. The clock generato...

DESCRIPTIONFRAM, or Ferroelectric Ram, is the coolest new data storage method that all the fashion magazines are talking about. Oh wait, no that's ...

DESCRIPTIONThe SparkFun micro:bit Breakout is a board that connects to the BBC micro:bit and expands the capabilities of the development platform b...

DESCRIPTIONThe 8-Pin SOIC to DIP Adapter is a small PCB that lets you adapt SOIC packages into a DIP footprint. These tiny boards are useful for mo...

DESCRIPTIONYou've always wanted to output analogue voltages from a microcontroller, the MCP4725 is the DAC that will let you do it! The MCP4725 is ...

DESCRIPTIONThis is a simple breakout board for the popular XBee product from Digi. This board breaks out all 20 pins of the XBee to a 0.1" standard...

DESCRIPTIONThe Raspberry Pi B+ has landed on the Maker World like a 40-GPIO pinned, quad-USB ported, credit card sized bomb of DIY joy. That's why ...

DESCRIPTIONNot just a simple breakout board, this microSD adapter goes the extra mile - designed for ease of use. To use with an Arduino, conn...

DESCRIPTION Here is a real time clock based on the DS3234 Real Time Clock IC. The DS3234 is a low-cost, extremely accurate SPI bus real-time clock ...

DESCRIPTIONThe smallest and easiest to use serial conversion circuit on the market! This board has one purpose in life - to convert RS232 to TTL a...

DESCRIPTION6 pin SOT-23 to DIP adaptor. Created to take SOT23 of various pin sizes breakout to DIP. This will work with 3-pin MOSFETs, BJTs, Voltag...

DESCRIPTION The XA1110 GPS Breakout is a small I2C-supported module built for easy hookup, thanks to the Qwiic Connect System. Equipped with the XA...

DESCRIPTION This is the breakout board for the thumb joystick. Pins are broken out to a 0.1" header and the board includes 4 mounting holes in the ...

DESCRIPTIONWith SD and MMC memory prices dropping, the time is right for mass storage and datalogging. This breakout board will allow you to breako...

DESCRIPTIONThis is a high-quality, easy to use 28 pin ZIF socket that is 0.3" wide. Makes for easy connecting or programming to DIP ICs. Uses high ...

DESCRIPTIONThe SX1509 Breakout is a 16-channel GPIO expander with an I2C interface €“ that means with just two wires, your microcontroller can ...

DESCRIPTION This a simple breakout board for the button pads. Each LED and button is brought out to the side connectors. The connectors are soldere...