Wearables

DESCRIPTION This is 30 feet of conductive thread spun from stainless steel fibre and wound on a plastic bobbin. Use it to sew up all of your e-text...

DESCRIPTIONThis is 12 meters of smooth conductive thread spun from stainless steel fiber and wound on a plastic bobbin. Use it to sew up all of you...

DESCRIPTION Drown out the voices in your head with a bone conduction transducer! This incredible speaker does not have a moving cone like most spe...

DESCRIPTION These DC powered heating pads are perfect for near-body heating applications. They get warm to the touch but not too hot. Simply apply...

DESCRIPTION This Pressure sensitive conductive sheet is cut from a continuous roll 36" wide. This conductive material (also known as "Velostat" or...

DESCRIPTIONMeasuring stretch forces isn't easy - unless you have some conductive rubber cord! This cord is 2mm diameter, and 1 meter long, made of ...

DESCRIPTION This LilyPad Coin Cell Battery Holder has a small slide switch installed on the board, in-line with the power so you can shut off you...

DESCRIPTION This is a watch band with a crystal acrylic case designed for use with the BBC micro:bit. You attach the micro:bit with ElecFreaks pow...

DESCRIPTION The DRV2605 from Texas Instruments is a fancy little motor driver. Rather than controlling a stepper motor or DC motor, its designed s...

DESCRIPTION The LilyPad Simple just got a whole lot... simpler. The Simple board has been updated to create the LilyPad USB by replacing the class...

DESCRIPTION These DC powered heating pads are perfect for near-body heating applications. They get warm to the touch but not too hot. Simply apply...

DESCRIPTION This is the SparkFun RGB and Gesture Sensor, a small breakout board with a built in APDS-9960 sensor that offers ambient light and col...

DESCRIPTION Circuit Playground Express is the next step towards a perfect introduction to electronics and programming. They've taken the original ...

DESCRIPTION The MicroView is the first chip-sized Arduino compatible module that lets you see what your Arduino is thinking using a built-in OLED ...

DESCRIPTION Here is a simple 5 pack of blue LEDs for LilyPad, or whatever else you can dream up. Light up the night! LilyPad is a wearable e-texti...

DESCRIPTION GEMMA V2 is a tiny wearable platform board with a lot of might in a 1" diameter package. Powered by a Attiny85 and programmable with a...

DESCRIPTION The SparkFun Little Soundie is a fun and easy-to-use audio playback device breaking out the VS1000D audio codec IC allowing this littl...

DESCRIPTION Attaching NeoPixel strips to your costume can be a struggle as the flexible PCBs can crack when bent too much. So how to add little do...

DESCRIPTION Mighty needles, sew like the wind! This needle set is the only one you'll need for any sort of hand sewing, especially using our condu...

DESCRIPTION This is LilyPad Arduino - the main board consisting of an ATmega328 with the Arduino bootloader and a minimum number of external compo...

DESCRIPTION This is a simple pack of five Red LilyPad LEDs that are still attached to one another, letting you snap the LEDs apart at your leisure...

DESCRIPTION Conductive hook & loop tape is just like the "Velcro" you've seen on clothes and bags, but is coated with silver to make it fully c...

DESCRIPTION This is a simple pack of five Green LilyPad LEDs that are still attached to one another, letting you snap the LEDs apart at your leisu...

DESCRIPTION Make your very own programmable NeoPixel goggles with 2 x 16 LED rings and an Adafruit Trinket. It even comes with a rechargeable LiPo...

DESCRIPTION RETIRED PRODUCT - We've stopped stocking this product or it has been retired by the manufacturer and is no longer for sale. This page ...

DESCRIPTION This is a simple pack of five Pink LilyPad LEDs that are still attached to one another, letting you snap the LEDs apart at your leisu...

DESCRIPTION This is a simple slide switch for the LilyPad. Use it as a simple ON/OFF switch, or to control LEDs, buzzers, sensors, etc. Each Li...

DESCRIPTION RETIRED PRODUCT - We've stopped stocking this product or it has been retired by the manufacturer and is no longer for sale. This page ...

DESCRIPTION The LilyPad E-Sewing ProtoSnap Kit is a great way to incorporate buttons and switches into an e-textile project without any programmin...

DESCRIPTION The LilyTwinkle is a tiny little LilyPad board designed to add some twinkle to your project. Even though it's as small as some of the ...

DESCRIPTION RETIRED PRODUCT - We've stopped stocking this product or it has been retired by the manufacturer and is no longer for sale. This page ...

DESCRIPTION Learn electronics with the Circuit Playground, a great way to practice programming on real hardware. It has built in sensors, LEDs and...

DESCRIPTION RETIRED PRODUCT - We've stopped stocking this product or it has been retired by the manufacturer and is no longer for sale. This page ...

DESCRIPTION This 60g conductive thread spool is 329 metres long and spun from stainless steel fiber. You can use it to connect electronics in wear...

DESCRIPTIONYour electronics can now see in dazzling colour with this lovely color light sensor. We found the best colour sensor on the market, the ...

DESCRIPTION This is a simple pack of five Yellow LilyPad LEDs that are still attached to one another, letting you snap the LEDs apart at your lei...