adafruit

DESCRIPTION What's better than a single LED? Lots of LEDs! These matrices use a driver chip that does all the heavy lifting for you: They have a bu...

DESCRIPTION Say hello to the 1.14" 240x135 Color TFT Display w/ MicroSD Card Breakout. It's the size of your thumbnail, with glorious 240x135 high...

DESCRIPTION If you'd like a compact colour display, with buttons and a joystick - this is what you're looking for. The Adafruit 1.3" Colour TFT Bo...

DESCRIPTION This is a screen for advanced hackers who like the look of the TFT screen found on the TFT Gizmo. The 1.54" IPS display has 240x240 16...

DESCRIPTION This little display is only 1.5" diagonal but has a high density 220 ppi, 240x240 pixel display with full-angle viewing. It looks a lo...

DESCRIPTION Easy e-paper finally comes to microcontrollers, with this breakout that's designed to make it a breeze to add a tri-color eInk display...

DESCRIPTION This "round rect" TFT display - is 1.69" diagonal and has high-density 220 PPI, 280x240 full-colour pixels with IPS any-angle viewing. ...

DESCRIPTION This little display breakout is the best way to add a small, colourful and bright display to any project. Since the display uses 4-wir...

DESCRIPTION If you are looking to add a small bright and colourful display to your next project this is the screen for you! This display uses 4-wi...

DESCRIPTION These 10-pin IDC cables are handy when programming or debugging a tiny board that uses 10-pin 1.27mm (0.05") pitch SWD programming conn...

DESCRIPTION With this 16 channel 12-bit PWM servo driver, using only two pins, you can control 16 free-running PWM outputs! You can even chain up 6...

DESCRIPTION The 16-Channel 12-bit PWM/Servo HAT will drive up to 16 servos or PWM outputs over I2C with only 2 pins. The on-board PWM controller w...

DESCRIPTION This adorable little coin cell battery holder is great for small, portable, or wearable projects. It holds two 20mm coin cell batteries...

DESCRIPTION This gorgeous IPS display breakout is the best way to add a small, colourful and bright display to any project, with excellent visibil...

DESCRIPTION Easy e-paper finally comes to microcontrollers, with this breakout that's designed to make it a breeze to add a tri-colour eInk display...

DESCRIPTION Woah, the cyber-future is here! Flexible E-Ink has been demo'd at high tech events for years but now you can actually get your hands o...

DESCRIPTION This little display breakout is the best way to add a small, colorful and bright display to any project. Since the display uses 4-wire...

DESCRIPTION Add some jazz & pizzazz to your project with a colour capacitive touchscreen LCD. This TFT display is 2.8" diagonal and bright wit...

DESCRIPTION Add some sizzle to your Arduino project with a beautiful large touchscreen display shield with built in microSD card connection and a ...

DESCRIPTION Woah, the cyber-future is here! Flexible E-Ink has been demo'd at high tech events for years but now you can actually get your hands o...

DESCRIPTION Easy e-paper finally comes to microcontrollers, with this breakout that's designed to make it a breeze to add a tri-colour eInk displa...

DESCRIPTION If you want to store calibration values, MAC addresses, non-secure access tokens, or other unique identifiers, EEPROM storage is a grea...

DESCRIPTION Add some jazz & pizazz to your project with a color touchscreen LCD. This TFT display is really big (3.2" diagonal) bright (6 whit...

DESCRIPTION The eTape Liquid Level Sensor is a solid-state sensor with a resistive output that varies with the level of the fluid. It does away wi...

DESCRIPTION This eTape Liquid Level Sensor is a solid-state sensor with a resistive output that varies with the level of the fluid. It does away w...

DESCRIPTION The simplest way to make an electromagnet is to get a solenoid, pass some current through it, and then get a piece of soft iron inside ...

DESCRIPTION The simplest way to make an electromagnet is to get a solenoid, pass some current through it, and then get a piece of soft iron inside ...

DESCRIPTION The simplest way to make an electromagnet is to get a solenoid, pass some current through it, and then get a piece of soft iron inside ...

DESCRIPTION Bring a little bit of Times Square into your home with this sweet 64 x 32 square RGB LED matrix panel. This matrix has 2048 bright RGB ...

DESCRIPTION Create some Times Square razzle dazzle with this sweet, ultra-high-density 64x64 RGB LED Matrix. These panels are typically used to ma...

DESCRIPTION By popular request, Adafruit has now made their 7-segment LED backpacks without the LEDs! These backpacks feature an HT16K33 I2C LED dr...

DESCRIPTION Because the Arduino (and Basic Stamp) are 5V devices, and most modern sensors, displays, flash cards and modes are 3.3V-only, many...

DESCRIPTION The 9 degrees of freedom, absolute orientation IMU fusion breakout, solves what can be the challenging problem of turning sensor data ...

DESCRIPTION If you've ever ordered and wired up a 9-DOF sensor, chances are you've also realised the challenge of turning the sensor data from an ...

DESCRIPTION Add motion, direction and orientation sensing to your project with this all-in-one 9-DOF sensor that is STEMMA QT ready for easy plug-...

DESCRIPTION Please note! This is NOT the subscription version of AdaBox! This is ONLY AdaBox001 that shipped out to AdaBox subscribers in Septembe...

DESCRIPTION RETIRED PRODUCT - We've stopped stocking this product or it has been retired by the manufacturer and is no longer for sale. This page...

DESCRIPTION AdaBox003 - The World of IoT (Curated by Digikey) is the perfect gift for folks who are just getting started in the world of DIY elect...

DESCRIPTION AdaBox004 - Making Things Dance is the perfect gift for folks who are just getting started in the world of DIY electronics. It's an ex...

DESCRIPTION This lovely little shield is the best way to add a small, colourful and bright display to any project. They took the popular 1.8" TFT ...

DESCRIPTION Pop this handy bonnet on your Pi Zero and get controlling servos in no time! It adds the capability to control 16 Servos with perfect ...

DESCRIPTION Easy e-paper finally comes to microcontrollers, with this breakout that's designed to make it a breeze to add a tri-colour eInk displa...

DESCRIPTION The Snake Eyes Bonnet is a Raspberry Pi accessory for driving two 128x128 pixel OLED or TFT LCD displays, and also provides four analo...

DESCRIPTION Detect trees of green, and red roses too with the new Adafruit AS7262 6-Channel Visible Light / Colour Sensor Breakout. This sensor fr...

DESCRIPTION Sometimes we wonder if robotics engineers ever watch movies. If they did, they'd know that making robots into slaves always ends up in...

DESCRIPTION Sometimes we wonder if robotics engineers ever watch movies. If they did, they'd know that making robots into slaves always ends up in...

DESCRIPTION Sometimes we wonder if robotics engineers ever watch movies. If they did, they'd know that making robots into slaves always ends up in...